Products
Block Jointing Adhesive
High strength adhesive for quick and firm laying of AAC blocks, fly ash bricks, concrete blocks, clc blocks, etc.
- Good Coverage
- Ready To Use
- Long Lasting Adhesion
- Consistent Quality
- Thin Joint
- Application Friendly
- Take the required quantity of water in a clean bucket, add LSR MATRIC BUILD® BLOCK JOINTING ADHESIVE recommended.
- Stir continuously for 5-10 minutes by using on electric stirrer or by hand to obtain a homogeneous lump free mix.
- Allow the resultant wet mortar to stand for about 5 minutes for the additives to dissolve.
- Re-mix again for about 2 minutes The mixture is now ready.
- Use the mix within 60 minutes.
- For best results it is advisable to use thin bed trowel of 3 to 5mm to have better contact and bonding.
Mix Plaster
High strength plaster for application over red bricks AAC blocks, fly ash bricks, concrete blocks.
- Ready To Use
- Good Coverage
- High Strength
- ECO Friendly
- Cost Effective
- Take the required quantity of water in a clean tray, add LSR MATRIC BUILD® READY MIX PLASTER recommended.
- Stir continuously for 5-10 minutes by using by hand to obtain a homogeneous material free mix.
- Allow the resultant wet material to stand for about 5 minutes for the material to dissolve.
- Re-mix again for about 2 minutes.
- Use the mix within 60 minutes.
- The mixture is now ready.
- For best results it is advisable to use thin bed trowel of 8 to 12mm to have better contact and bonding.
Tile Adhesive (MFT-501)
High strength adhesive for quick and firm laying of tiles.
- The substrate of oil stains bond inhibiting compounds. Remove any loose particles dust, and laitance.
- Ensure that the surface is flat (hard and rigid) for the given application.
- Gradually add 3 parts of powder to 1 part of water (by volume) and mix it to a smooth workable paste.
- Always add LSR MATRIC BUILD® TILE ADHESIVE powder to water.
- After mixing allow the paste to stand for 2 minutes for it to mature.
- Do not attempt to extend the pot life by adding the more water to the mix.
- Firmly press the tile into the LSR MATRIC BUILD® to ensure good initial bonding.
- After 24 hours grouting can be done on tiles and stones.
Tile Adhesive (MWT-601)
High strength adhesive for quick and firm laying of tiles.
- The substrate of oil stains bond inhibiting compounds. Remove any loose particles dust, and laitance.
- Ensure that the surface is flat (hard and rigid) for the given application.
- Gradually add 3 parts of powder to 1 part of water (by volume) and mix it to a smooth workable paste.
- Always add LSR MATRIC BUILD® TILE ADHESIVE powder to water.
- After mixing allow the paste to stand for 2 minutes for it to mature.
- Do not attempt to extend the pot life by adding the more water to the mix.
- Firmly press the tile into the LSR MATRIC BUILD® to ensure good initial bonding.
- After 24 hours grouting can be done on tiles and stones.
Tile Adhesive (MGMT-701 )
High strength adhesive for quick and firm laying of tiles.
- The substrate of oil stains bond inhibiting compounds. Remove any loose particles dust, and laitance.
- Ensure that the surface is flat (hard and rigid) for the given application.
- Gradually add 3 parts of powder to 1 part of water (by volume) and mix it to a smooth workable paste.
- Always add LSR MATRIC BUILD® TILE ADHESIVE powder to water.
- After mixing allow the paste to stand for 2 minutes for it to mature.
- Do not attempt to extend the pot life by adding the more water to the mix.
- Firmly press the tile into the LSR MATRIC BUILD® to ensure good initial bonding.
- After 24 hours grouting can be done on tiles and stones.
Contact Us